Enhanced hollow fiber membrane performance via semi-dynamic layer-by-layer polyelectrolyte inner surface deposition for nanofiltration and forward osmosis applications

The layer-by-layer (LBL) polyelectrolyte deposited membranes have drawn increasing attention in various applications due to the ease of selective layer formation and their stability and versatility. In this study, the LBL deposition was performed at the inner surface of the polyethersulfone (PES) hollow fiber substrate to form composite nanofiltration (NF) membrane. The semi-dynamic deposition procedure was adopted with the aid of syringes. The newly developed inner deposited (id-LBL) membranes were then tested in NF and forward osmosis (FO) applications and the performance were compared with outer surface deposition as well as some literature data. The id-LBL membranes could not only withstand higher operating pressure but also possess superior hardness rejection especially in high concentration mixed salt solutions (more than 95% rejection to Mg²⁺ and Ca²⁺ in a 5000 ppm total dissolved salt (TDS) mixture under 4.8 bar). As for the FO process, with only two layer deposition, the id-LBL membranes also demonstrated significant performance improvement with increased water flux (up to 70 L/m² h using 0.5 M MgCl₂ as draw solution in active layer facing draw solution configuration) and reduced salt leakage (around 0.5 g/m² h using 1 M MgCl₂ draw solution in active layer facing feed water configuration). This study suggests that for hollow fiber substrate, the inner surface is more suitable for the formation of the selective layer via LBL deposition than the outer surface.     

Performances at high temperature of RC bridge decks strengthened with EBR-FRP

Fiber reinforced polymer (FRP) can be successfully used to externally strengthen reinforced concrete (RC) bridges where fire is not a primary concern. Nevertheless, common maintenance activity on a bridge deck, such as the laying of bituminous paving, can easily lead the FRP to temperatures higher than the glass transition temperature, T_g. Exceeding T_g does not necessarily imply a drastic reduction in strength and stiffness of the reinforcement. Nevertheless, the softening of the resin implies a drastic reduction in its adhesion properties. Therefore, the efficiency of the strengthening system for existing structures, which mainly depends on the effectiveness of the bond between FRP and concrete, is significantly affected by temperature.The relationships suggested by Italian and American codes in order to evaluate the limit strain for FRP debonding at normal temperature are modified to take into account the effect of high temperature. Then, performances at high temperature of RC bridge decks strengthened with externally bonded FRP plates (EBR) are investigated by considering thermal fields in the structural members which are different from the normal ones. Both fire and the laying of bituminous paving on the decks are considered. In addition, the thicknesses of the slabs and the protective layer are varied to assess their influence on the thermal field in the slabs. The results are discussed with reference to both ultimate and serviceability limit states.     

Hygrothermal deformation of orthotropic nanoplates based on the state-space concept

This paper deals with the investigation of the effect of hygrothermal conditions on the bending of nanoplates using Levy type solution model employing the state-space concept. The nanoplates are assumed to be subjected to a hygrothermal environment. The two-unknown function plate theory is used to derive the governing differential equations on the basis of Eringen's nonlocal elasticity theory. The governing equations contain the small scale effect as well as hygrothermal and mechanical effects. These equations are converted into a set of first-order linear ordinary differential equations with constant coefficients. Analytical solution of bending response for nanoplates under combinations of simply supported, clamped and free boundary conditions is obtained. Comparison of the results with those being in the open literature is made. The influences played by small scale parameter, temperature rise, the degree of moisture concentration, boundary conditions, plate aspect ratio and side-to-thickness ratio are studied.     

涤纶预拉伸丝后加工过尾的研究

从原料、后加工设备、接尾工具、作业方法等方面对影响涤纶预拉伸丝(PET POY)后加工过尾的主要因素进行了研究。生产实践证明,通过改善PET POY表面特性,调整后加工丝道的整体平顺性,设定合理的接尾气压和捻接时间,使用接尾前后冷拉伸的操作等方式,可以提升PET POY的后加工过尾成功率。通过上述改善措施,过尾成功率能够提升至90%以上。     

Al2O3/Yttria‐Stabilized Zirconia Hollow‐Fiber Membrane Incorporated with Iron Oxide for Pb(II) Removal

Removal by absorptive ceramic membranes can simultaneously absorb and separate metal ions from water. Alumina/yttria‐stabilized zirconia (Al₂O₃/YSZ) hollow‐fiber membranes, fabricated using phase inversion and sintering process, were deposited with iron oxide by an in‐situ hydrothermal process. The results showed that α‐Fe₂O₃ was produced and incorporated across the membranes. A reduction in flux was recorded with the deposition of α‐Fe₂O_3. However, it improved the adsorption capacity for heavy metal adsorption. The adsorption‐separation test demonstrated that the optimized membrane is able to completely remove Pb(II) ions after two hours.     

高功率光纤激光器光纤器件封装应力影响研究

高功率激光器无源器件制作过程中封装不当引入的应力,会导致信号光光束质量劣化和光纤温升,为了解决此问题,理论分析了光纤形变对信号光模式分布的影响,利用有限元方法建立包层光导致光纤发热模型,实验研究了不同封装方式对光纤发热情况和信号光光束质量的影响。实验表明,应力导致的光纤形变会造成信号光M2值在受力方向上略微变小而其垂直方向上变大,在输出100 W信号光时,施加应力导致的M2值的变化最高为0.39,与仿真结果相符。在光纤温升方面,相比于使用硬质胶水带来的12 ℃温升,使用硅橡胶封装的剥离器将温升控制在5 ℃以内,且其封装应力引入的M2值的变化在0.05以内。     

川北某黑色页岩型铼矿工艺矿物学研究

通过矿相显微镜、扫描电镜、电子探针、X射线能谱元素面分析等多种手段综合研究了川北某黑色页岩型铼矿中铼的赋存状态。样品为黑色页岩,有机碳含量较高。粘土矿物总量为14.6%,黄铁矿含量16.2%,石英含量37.7%。样品具典型的粘土结构,矿物粒度微细。铼有两种赋存状态,一种呈类质同象形式赋存于黄铁矿内,另一种则以分散形式存在。典型黄铁矿测点Re平均含量为0.024%。黄铁矿是Re的重要载体矿物。建议通过浮选分离黄铁矿,从而实现Re的富集。      

柠条的纤维特性及其双螺杆CMP制浆性能研究

以柠条为原料，分析了其化学组分和纤维形态，并探讨了柠条双螺杆CMP法的制浆工艺以及浆料的纤维形态和成纸的物理性能。研究结果表明：与针、阔叶木相比，柠条原料中纤维素和综纤维素质量分数较低，苯醇抽出物和热水抽出物质量分数较高，柠条纤维长度总体偏短，木质部和皮部的纤维质量平均长度分别为0.621和0.819 mm，还存在部分杂细胞。采用3.5% Na₂SO₃和1.5% NaOH常温预浸12 h、90℃汽蒸1 h后再用双螺杆挤浆机在质量分数35%下进行搓丝，并结合高浓盘磨机磨浆，所得CMP浆得率可达73%。柠条CMP浆基本保持了纤维原有的长度，质量平均长度达0.650 mm，长宽比为32.7，纤维解离较好，但分丝帚化情况不理想，含有部分纤维束和杂细胞。当加拿大游离度为300 mL时，柠条CMP浆成纸的环压强度指数和松厚度较高，分别为8.67（N·m）/g和2.56 cm³/g，抗张指数为19.6（N·m）/g，本色浆白度较高，达50%（ISO）。柠条CMP浆适合配抄瓦楞原纸等包装用纸，漂白后可配抄新闻纸和白板纸。     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

生物质纤维和改性木质素对聚乳酸结晶性能的影响

采用改性木质素(MZS)作为成核剂,生物质纤维(BF)作为增强剂,通过双螺杆挤出机制备了生物降解的聚乳酸(PLA)/BF/MZS材料。采用差式扫量热仪(DSC)、电子万能试验机和扫描电子显微镜(SEM)分析了BF和MZS对PLA材料性能的影响。结果表明,BF和MZS有效提高了PLA的结晶能力和力学性能。当BF和MZS的含量分别为15%和1%时,PLA材料结晶度提高至67.1%,在50℃/min降温速率下仍具有较高的结晶能力。105℃等温结晶时,15%BF和1%MZS的PLA材料半结晶时间降低至9.0 s,比纯PLA缩短了72.2%。当PLA含有3%BF和1%MZS时,拉伸强度和冲击强度分别为70.1 MPa和7.4 kJ/m^2,比纯PLA分别提高了7.8%和10.4%,根据SEM显示,当BF含量为3%时,在PLA材料中分布较均匀。